View V23870-A2111-B600_619888.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary Data Sheet
V23870-A211x-xx00(*)
Bi-Directional Pigtail SFF Transceiver 155 Mb/s, 1310 nm Tx / 1310 nm Rx
FEATURES * Integrated Beam Splitter * Bi-Directional Transmission in a single optical window * Single fiber solution, singlemode fiber pigtail with different connector options * Data rate up to 155 Mbit/s * FP Laser Diode with Multi-Quantum Well structure, wavelength 1310 nm * Class 1 Laser Product * Incorporated laser driver and PIN-TIA Receiver with post-amplifier * 2x5 Small Form Factor Package with Multisource Footprint *) Ordering Information
Absolute Maximum Ratings Operating case temperature V23870-A2111-xx00 ....................... 0 to 70 C V23870-A2112-xx00 .................... -40 to 85 C Storage Ambient Temperature ................. -40 to 85 C Supply voltage .................................................. 3.53 V Soldering Conditions Temp/Time Iron Soldering only .................... 400 C / 10 s
V23870 - A211x - xx00
Average Launched Power: 2: -8 ... -13 dBm Temperature Range: 1: 0 ... +70 C 2: -40 ... +85 C Connector: A: Pigtail Only B: SC C: SC/APC 8 F: MU H: MU-J K: LC Coupling: (Tx/Rx, Signal Detect) 1: AC/AC, PECL SD 2: DC/DC, PECL SD 5: AC/AC, TTL SD 6: DC/DC, TTL SD
Fiber Optics
JULY 2002
DESCRIPTION The Infineon BIDI(R) transceiver - part of Infineon's Small Form Factor transceiver family - is based on the Physical Medium Depend (PMD) sublayer and baseband medium. Infineon's BIDI-TRX is designed to handle multiple data rates and can be designed into Fast Ethernet, FDDI, Fiber Channel, ATM-155, SDH STM-1, SONET OC-3, CCTV and other applications as well as different FTTx applications according to the 100 Mbps EFM standard (IEEE 802.3ah). It is suitable for both, short haul applications and distances of 20 km and beyond. The appropriate fiber optic cable is the 9m singlemode fiber pigtail with different connector options. The Infineon BIDI transceiver is a single unit comprised of a transmitter, a receiver, WDM filter or beam splitter, and a singlemode fiber pigtail. This design frees the customer from many alignment and PC board layout concerns. This transceiver operates at 155Mb/s from a single power supply (+3.3 V). The full differential data inputs and outputs are PECL and LVPECL compatible. Functional Description of 2x5 Pin Row Transceiver This transceiver is designed to transmit and receive serial data via a singlemode cable. Functional Diagram
Fiber Optics
2
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
The receiver component converts the optical serial data into PECL compatible electrical data (RD and RDnot). The Signal Detect (SD, active high) shows whether an optical signal is present. The transmitter converts PECL compatible electrical serial data (TD and TDnot) into optical serial data. Data lines are differentially 100 terminated. The transmitter contains a laser driver circuit that drives the modulation and bias current of the laser diode. The currents are controlled by a power control circuit to guarantee constant output power of the laser over temperature and aging. The power control uses the output of the monitor PIN diode (mechanically built into the laser coupling unit) as a controlling signal, to prevent the laser power from exceeding the operating limits. Single fault condition is ensured by means of an integrated automatic shutdown circuit that disables the laser when it detects laser fault to guarantee the laser Eye Safety. The transceiver contains a supervisory circuit to control the power supply. This circuit makes an internal reset signal whenever the supply voltage drops below the reset threshold. It keeps the reset signal active for at least 140 milliseconds after the voltage has risen above the reset threshold. During this time the laser is inactive. The laser can be disabled by the TxDis input.
Technical Data The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Recommended Operating Conditions Operating Temperature Range at Case Operating Temperature Range at Case Power Supply Voltage Transmitter Data Input Differential Voltage Receiver Input Center Wavelength C 1500 1600 nm VDIFF 250 1600 mV
1 2
Symbol TC TC VCC-VEE
Min. 0 -40 3.1
Typ.
Max. +70 +85
Unit C C V
3.3
3.53
1 2
For V23870-A2111-xx00 For V23870-A2112-xx00
Fiber Optics
3
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
Transmitter Average Launched Power Emission wavelength center of range3 Spectral bandwidth (RMS) Temperature coefficient of emission wavelength Extinction Ratio (Dynamic) Jitter (pkpk) Rise Time (20% - 80%) Fall Time (20% - 80%) Eye diagram RIN Noise Reset Threshold Reset Timeout5 Power on Delay Shut Off Time for TxDis Max Tx Supply Current
5 5 4
Symbol Pout,max (T) ER JPP tR tF
Min. -13 1270
Typ.
Max. -8
Unit dBm nm nm nm/K dB
1310
1350 3.0 0.5
8.5 1 2.5 2.5
ns ns ns
ITU G.957 mask pattern RIN VTH tRES tPWR_ON tDIS ITX 90 2.5 140 88 2.75 240 111 -120 2.99 560 140 6 135 dB/Hz V ms ms ms mA
3 4 5
Popt = Pout,max at T=25C Rise and fall times are measured with the OC-3 filter ON Laser power is shut down if power supply is below VTH and switch on if power supply is above VTH after tRES.
Fiber Optics
4
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
Receiver Receiving wavelength center of range Sensitivity (Average Power)7 Saturation (Average Power) Signal Detect Assert Level
8 9 6
Symbol R PIN PSAT PSDA PSDD PSDAPSDD
Min. 1270
Typ. 1310
Max. 1350 -21
Unit nm dBm dBm
-3.0 -22 -31 0.5 4 6
dBm dBm dB
Signal Detect Deassert Level Signal Detect Hysteresis
Signal Detect Assert Time Signal Detect Deassert Time Data Output Differential Voltage Rise/Fall Time Max Rx Supply Current
11 10
tASS tDAS VDIFF tR; tF IRX 60 0.4 0.8
100 350 1.0 1.5 130
s s V ns mA
Module Electro-Optical Characteristics Optical Isolation
12
Symbol ORL
Min. 14
Typ.
Max.
Unit dB
6 7
Popt = Pout,max at T=25C Minimum average optical power at which the BER is less than1x10E-10. Measured with a 1023 -1 NRZ PRBS as recommended by ANSI T1E1.2, SONET OC-3, and ITU G.957. 8 An increase in optical power above the specified level will cause the SIGNAL DETECT output to switch from a Low state to a High state. 9 A decrease in optical power below the specified level will cause the SIGNAL DETECT to change from a High state to a Low state. 10 AC/AC for data. Load 50 to GND or 100 differential. For dynamic measurement a tolerance of 50mV should be added. 11 Supply current excluding Rx output load. 12 Source wavelength is 1550 nm, BiDi Tx and Rx is Off
Fiber Optics
5
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
Fiber Data The mechanical fiber characteristics are described in the following table. Fiber Characteristics Mode Field Diameter Cladding Diameter Mode Field/Cladding Concentricity Error Cladding Non-circularity Mode Field Non-circularity Cut off Wavelength Jacket Diameter Bending Radius Tensile Strength Fiber Case Length 1270 0.8 30 5 0.8 1.2 1 Min. 8 123 Typ. 9 125 Max. 10 127 1 2 6 Unit m m m % nm nm mm mm N m
Fiber Optics
6
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
Pin Description Pin Name VEEr Receiver Signal Ground VCCr Receiver Power Supply SD Signal Detect Level/ Logic N/A N/A see options on page 1 Pin# 1 2 3 Description
Normal Operation: Logic "1" Output, represents that light is present at receiver input Fault Condition: Logic "0" Output Recommended Termination of 510 to Veer for PECL
RD- RD+ VCCt VEEt TxDis TD+ TD- MS
Received Data Out Not Received Data Out
Transmitter Disable/Enable Transmit Data Transmit Data Not Mounting Studs
PECL PECL N/A N/A TTL-Input PECL PECL N/A
4 5 6 7 8 9 10 MS1 MS2 T1 T2 T3 T4
HL
Housing Leads
N/A
Transmitter Power Supply Transmitter Signal Ground A low/open signal switches the laser on. A high signal switches the laser off. Transmitter Data In Transmitter Data In Not Mounting Studs are provided for transceiver mechanical attachment to the circuit board. The transceiver Housing Leads are provided for additional signal grounding. The holes in the circuit board must be included and be tied to signal ground.
Fiber Optics
7
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
Technical drawings
13.50 .531 9.71 .382
3 .118
3.92 .154
12 .472
0.38 .015 7.11 .280 2X 4.56 .180 3.10 .122
0.25 .010 17.79 .700
1.78 .070
49.01 1.930
TEMPERATURE MEASUREMENT LOCATION
1.07 .042
20.19 .795
+10 0 +.394 .877 - .000 22.27
13.50 .531 5.15 .203
1.40 .055
10.16 .400 20X
0.81 .032
21.34 .840 1.84 .072
23.88 .940
13.34 .525
NOTES: 1. FIBER AND CONNECTOR NOT SHOWN. 2. REFER TO PACKAGE OUTLINE OF THE SMALL FORM FACTOR TRANSCEIVER MULTISOURCE AGREEMENT FOR DIMENSIONS NOT SHOWN.
15.75 .620
FRONT OF BEZEL Recommended PCB Thickness 0.1 (2.54) max.
Circuit Board Layout
Fiber Optics
8
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
EYE SAFETY This laser based singlemode transceiver is a Class 1 product. It complies with IEC 60825-1 and FDA 21 CFR 1040.10 and 1040.11. To meet laser safety requirements the transceiver shall be operated within the maximum operating limits. Caution All adjustments have been made at the factory prior to shipment of the devices. No maintenance or alteration to the device is required. Tampering with or modifying the performance of the device will result in voided product warranty. Note: Failure to adhere to the above restrictions could result in a modification that is considered an act of "manufacturing," and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)).
APPLICATION NOTES Transceiver Assembly/Soldering Recommended requirements * avoid temperatures on fiber and connector above 85C * only iron soldering permitted * single pin or simultaneous pin soldering valid
Type
Iron - soldering
Conditions
iron tip temp. solder time
Standard
< 400 C IEC 68 2-20 test Tb, methode 2 < 10 sec
Fiber Optics
9
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
AC/AC coupling
Vcc 3.3V
C3 L1 C1 L2 C2
Vcc SerDes 3.3V
TxVcc (6) RxVcc (2) TxVee (7) TD+ (9) Vcc Ser Data Out+ TD- (10) R1 TxDis (8) SD (3) SD R7 Rd- (4) R3 R4 Ser Data InReceiver Rd+ (5) Ser Data In+ R2
Laser Driver
100 Ohms
ECL/PECL Driver
Ser Data Out-
Serializer/ Deserializer
Limiting Amplifier
SFF Transceiver
RxVee (1)
R5
R6
L1, L2: 1...4.7 H C1, C2, C3: 4.7...10 F R1, R2: biasing of outputs depending on Serializer R3, R4: 127 Ohms R5, R6: 80 Ohms R7: 510 Ohms for PECL signal detect, open for TTL Place R1/2/3/4/5/6 as close to SerDes chip as possible
Fiber Optics
10
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver
DC/DC coupling
Vcc 3.3V
C3 L1 C1 L2 C2
Vcc SerDes 3.3V
TxVcc (6) RxVcc (2) TxVee (7) TD+ (9) R6 R7 C6 R9 TD- (10) C7 R4 TxDis (8) SD (3) R8 SD R10 C4 Rd- (4) R1 Rd+ (5) C5 Ser Data In+ Ser Data InReceiver R5 Ser Data OutVcc Ser Data Out+
Laser Driver
ECL/PECL Driver
Serializer/ Deserializer
Limiting Amplifier
SFF Transceiver
RxVee (1)
R2
R3
L1, L2: 1...4.7 H C1, C2, C3: 4.7...10 F C4, C5, C6, C7: 100 nF R1: 100 Ohms R2, R3: 150 Ohms R4, R5: biasing of outputs depending on Serializer R6, R7: 127 Ohms R8, R9: 80 Ohms R10: 510 Ohms for PECL signal detect, open for TTL Place R1/4/5 as close to SerDes as possible Place R2/3 as close to transceiver as possible
Fiber Optics
11
V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver

▲Up To Search▲

Price & Availability of V23870-A2111-B600

	To Download V23870-A2111-B600 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .